Save Water and Energy By Home Plumbing Systems

Home Plumbing Systems

Water is essential as air, but we should not waste it. Usually, per day a typical American household uses more than 300 gallons of water – according to the Environmental Protection Agency (EPA). Whereas 30 percent of water usage occurs outdoors and 70 percent is used indoors.

However, we are environmentally very conscious about water conservation in our daily lives; additionally, for the residential plumbing fixtures, the water usage limits by the Energy Policy Act in 1992 Congress. Prior to the act, toilets were required to use 1.6 gallons of water per flush, as an example. But toilets use 3.5 gallons per flush. Since raising the bar for mandating low-consumption fixtures, some states in the USA have adopted new standards. One of the most high-efficient is toilets using 1.28 GPF.

Anyhow, as a water user, there are many ways you can reduce water consumption smartly. At the same time, this will help in saving energy. This guide will discuss a few tips on how you can try this.

Tips for Saving Water and Energy

  1. Inspect Home Plumbing to Find Out Issues

If you can detect the plumbing issues very early, it will be easier for you to fix them.

– Check out the bath, sink or shower hardware for any leakage.

– Inspect below the sink to check pipes.

– Inspect your utility room, as well as pipes in your basement.

– You can check out toilet leaks by adding a few drops of food color to the tank. After 10 to 15 minutes, check out whether the color has changed or not. And inspect the floor as well around the toilet this will show you the broken seal.

– Inspect the outdoor hoses or faucets as well.

If you find any defective pipes or fixtures, then you have to replace or fix the pipes. Once you fix the leaking faucets or pipes, this could save up to 20 gallons of water each day.

  1. Using the low-flow fixtures

You can effortlessly replace existing fixtures without disturbing any plumbing installation if you have low-flow fixtures. This is also a very effective way of water conservation.

– Using low-flow fixtures can reduce water consumption by up to 30 percent more than any conventional fixtures.

This helps use 40 percent less water consumption than any normal faucets.

If your toilet uses more than 5 gallons per flush, replace this with a new one.

The best thing is that a low-flow fixture also helps reduce electricity consumption only if your property uses a water booster pump.

  1. Water Heaters for Energy Consumption

This can achieve significant energy savings if you are using a water heater since it reduces the volume of water flow.

– One of the most energy-efficient models is replacing an old heater with a new one.

– Tankless heaters reduce energy consumption.

If you are using a tank-based heater, ensure to maintain it properly to get adequate performance at optimal levels.

– You can also prevent scalding plus reduce energy expenses when you keep the water heater at 120 degrees Fahrenheit.

– To avoid any heat losses between the plumbing fixtures and water heater make sure to insulate pipes.

  1. Inspect Supply Hoses of Washing Machine

Generally, washing machines use large amounts of water to impact your water bills.

– Check out the floor beneath the washing machine for any leaking signs or drips.

– Inspect the water supply from end to end to check out any damage signs.

– If you are using rubber hoses, then ensure to replace them every five years since these are most likely to damage.

  1. Develop Garden Management Practice

– Most homeowners focus on indoor water usage or energy consumption. You should also focus on outdoor water or energy consumption.

– Use thick pipes around trees to reduce evaporation.

– You can also save rainwater to use to maintain your landscape.

– Bring an intelligent sprinkler controller that helps save 40 gallons of water per day.

  1. Maintain Drain As Well

– You can use an environment-friendly drain to prevent clogging because chemical systems can damage the drain sooner.

– To keep out of drain pipes, you can use strainers.

– Try to keep out oil or fats from drain pipes.

– Maintain the garbage disposal guideline to avoid any damage to the drain pipes.